How to replace a pull cord on a 3.5 hp tecumseh engine
With all fluids now removed we can do this without causing further problems. The next part of the servicing requires tipping the lawnmower up to access the blade underneath. There are smaller alternatives that will do a great job including Silverline 104616 Oil and Fluid Extractor Pump, 4 L I use a Pela 6000 Oil Pump – Oil Extractor/Oil Extraction Kit. Just use an oil extractor to remove the fuel and please dispose of it in an environmentally friendly way. You do not need to run the lawnmower out of petrol/gas as this can pull any dirt from the bottom of the petrol/gas tank into the carburettor and cause further problems. If your lawnmower engine runs, then I suggest running it for a few minutes to warm up the oil before extracting. Not only will you have a massive white smoke problem when the lawnmower restarts, but it may also stop you being able to pull over the lawnmower engine at all. Tecumseh lawnmowers, like many others, really don’t appreciate being tipped up as it sends fuel and oil into areas of the engine it shouldn’t be. Using an oil extractor eliminates the need to tip the lawnmower up or over to remove the fluids. With this in mind, I strongly recommend using an oil extractor to remove all the fuel and oil from the engine. With a Tecumseh engine, you need to re-fit a lot more parts to be able to test the lawnmower and it’s very time-consuming. With most of the lawnmower engines I service or repair, it only takes a few minutes to refit the carburettor and test the lawnmower once servicing is complete. Please do not skip this section because it will save you from making a massive error when re-building the lawnmower after servicing the carburettor. You can find lots more information and start repairing lawnmowers for profit by checking out my online training here Remove All Oil And Fuel From The Lawnmower Don’t worry, I’ll cover all parts of the engine service, but there a few key steps to follow at the very beginning.
![how to replace a pull cord on a 3.5 hp tecumseh engine how to replace a pull cord on a 3.5 hp tecumseh engine](https://i.ytimg.com/vi/UW2FIqGCW3c/hqdefault.jpg)
I always start any servicing by removing any old oil and fuel from a lawnmower. There is a specific section for Tecumseh. Many of the service parts you may require can be found at my recommended products page.
![how to replace a pull cord on a 3.5 hp tecumseh engine how to replace a pull cord on a 3.5 hp tecumseh engine](https://m.media-amazon.com/images/I/413EI3ocDTL._AC_SS450_.jpg)
These simple engines can easily be serviced in around an hour if you follow the instructions I’m about to share, In fact, In my opinion, the hardest part about servicing these engines is removing the parts (and fluids) in the correct order so let’s get started. I have repaired thousands of lawnmowers for profit over the years including hundreds of Tecumseh engines.
HOW TO REPLACE A PULL CORD ON A 3.5 HP TECUMSEH ENGINE HOW TO
I’m going to show you my complete guide for servicing a Tecumseh lawnmower engine in this article, including how to service the carburettor and solve any hunting and surging issues you may have. We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to and affiliated sites.How To Service A Tecumseh Lawnmower Engine- A Complete Guide This video description and commentaries contains affiliate links, which means that if you click on one of the product links, I could receive a small commission.
![how to replace a pull cord on a 3.5 hp tecumseh engine how to replace a pull cord on a 3.5 hp tecumseh engine](https://i.ytimg.com/vi/IL25Nblnmlg/hqdefault.jpg)
Any reliance you place on such information is therefore strictly at your own risk. We will not accept any liability for damage or injury caused while following this guide. This video intended for general information only. Other photo and video guides you can find on our website: